- 1 WHAT IS the ESP32?
- 1.1 ESP32 Boards we are testing
- 1.2 CONNECTING TO THE ESP32
- 1.3 Installing "ESP32 Arduino" into the Arduino ISP
- 1.4 DOWNLOAD AND INSTALL THE ESP32 USB DRIVERS
- 1.5 CONNECTING YOUR ESP32 Module and TESTING IT
- 1.6 ESP32 EXAMPLE SKETCHES
- 1.7 ESP32 Memory Size Questions
- 1.8 ESP32 Reference Publications
- 1.9 NOTE for Future USE
WHAT IS the ESP32?
ESP32 is a series of low-cost, low-power system-on-a-chip micro-controllers designed by Espressif in Shanghai, China. It has integrated Wi-Fi and dual-mode Bluetooth radios. It has many of the capabilities of the Arduino and can be programmed with the Arduino IDE software and so is an easy upgrade path to wireless communications for Arduino users.
The ESP32 is an upgrade of the earlier ESP8266 and adds a faster dual-core processor and Bluetooth interface. On the left is a block diagram of the many features inside the ESP32.
The ESP32 is usually seen as a metal-cased module (In the red rectangle in the section below) that is then placed on slightly larger boards with added components. The metal-cased product includes a crystal oscillator, a flash memory chip. capacitors etc. See the UNcased photo at right. The Metal-cased module has been approved by European and FCC testers. This is a major plus: it can be included in other new products without more testing.
ESP32 Boards we are testing
(Both of these boards have 38 pins on 0.1 inch centers) If you Look-Closely-Now you will see the pinouts are the same.
- "ESP32 Dev Kit V2"
By Espressif, maker of the ESP32 Chips. About $15 Amazon example The pin-out diagram on the right shows the connections to the ESP pins, power, ground etc. Note there are two small pushbuttons labelled BOOT and EN
By Ai-Thinker. About $12 Amazon ExampleUsually received with firmware called nodeMCU which supports the LUA programming language as well as C++.
CONNECTING TO THE ESP32
The ESP32 development boards have pins (19 pins each side, 0.1 inch spacing, 1.0 inch spacing between rows). This does not work for typical breadboards, but two breadboards can be used as in the photo on the left. The example here was used for testing many of the example sketches below.
We are also working on a "Sensor Shield" which ESP32 would plug into and which would provide easy-to-use 3-pin connections for sensors and actuators.
Installing "ESP32 Arduino" into the Arduino ISP
You need to start with the latest Arduino IDE software. Go to the download page HERE and scroll to Download the Arduino IDE. In the green box on the right, find your system. For Windows, use Windows Installer unless you have an earlier version and know how to just add the ZIP file. Run the installed Arduino IDE system to make sure it works..
Next you will install ESP32 capability into the Arduino environment. This installs board definitions, code libraries and much more, to allow you to program the ESP32 in the familiar Arduino ISP software. This is what we use to write and test the example sketches below. Here are the steps:
 At the top menu bar go to File and then Preferences. In the lower part of the screen you will see something like this:
(I already had an entry for ESP8266, which you see here) But notice the square icon at far right. Click It
Now you will get a pop-up that looks like this:
Add a line in the box (you can cut/paste) :
https://dl.espressif.com/dl/package_esp32_index.json then click OK and back at Preferences again click OK
You have told the Arduino IDE where to find the ESP32 information. Now you need to actually get it downloaded and installed. This will take quite a while, once you start.
 Have the Boards Manager get the ESP32 information and install it. At the top menu bar go to Tools then Board then Boards Manager You'll see a screen like this:
In the field "Filter Your Search" enter ESP32
Now you should see the esp32 by Espressif Systems entry like this:
Move you mouse down into it, and at the lower right click on Install. (Mine shows it already installed in the photo)..
NOW watch the status bar at the lower edge of the box. Get coffee or Other: It will take quite a while.
DOWNLOAD AND INSTALL THE ESP32 USB DRIVERS
You probably do not have the USB drivers installed to support the CP2012 USB interface chip on your ESP32. Here's what to do:
Get and Install the Drivers: HERE: You need to pick the version for your version of Windows. For WIN7 pick the first (default) entry.
Put the downloaded ZIP file in a new folder. UNZIP it there. Now there are two possibilities:
 You plug your ESP32 into a USB connection and Windows prompts you to install a driver
1. Use the dialog to browse for the driver location
2. Locate the driver folder (that you previously unzipped)
3. Follow the instructions
 Manual Install
1. Using Windows File Explorer, locate the driver folder (that you previously unzipped)
2. Determine if you have 32-bit or 64-bit Windows
3. Double click to run the .exe file named CP210xVCPInstaller_xnn.exe (where xnn is x64 for 64-bit and x86 is for 32-bit)
4. Follow the instructions
That was not a lot of fun. But NOW the fun begins!
CONNECTING YOUR ESP32 Module and TESTING IT
You need a "Micro-USB" cable to run your ESP32. Make SURE it is a real USB data cable, not a charger-only cable. (I got burned-and-confused with that!)
If you do not use a breadboard at this point, make sure the ESP32 will be on a non-conductive surface, like a magazine. Like MAKE, or The New Yorker, or Vermont Life, or any of those dumb catalogs that clog up your mailbox... Anyway, Plug the USB cable into your ESP32 and then into your computer's USB port.
A Red LED should light up on your ESP32. That shows it is getting 5 Volt power over USB (An onboard regulator will provide 3.3V for the ESP32 chips).
Now: Start the Arduino IDE and let's get things set up:
 Select your particular ESP32 board in the Arduino IDE. Click Tools then Board and you should see something like this:
Select your board in the pulldown on the right. (You may have to scroll that section down).
 Select your PORT. Click Tools then Port: . You should see a new COM port, labelled COM4 or something. Select it. (Mine shows an Arduino also connected).
 Open a New sketch: (Highlight and remove any template lines so you have a blank sketch page).
 In the section below "ESP32 EXAMPLE SKETCHES" click on YourESP32 Sketch WIFI Scan . Copy and paste it into your blank IDE page.
 At the top, click the button labelled Verify At the bottom green area you should see:
After several seconds (or longer for the first compile) you should see:
IF that's OK, now Upload your sketch! Click the Upload button:
After several seconds you should see a "Connecting" message:
If all goes well, in a few seconds you show see this message:
See the sketch work:
The Scan Wifi sketch tells your ESP32 to activate it's WiFi radio and scan for any WiFi networks it can find. You will see the results on the Serial Monitor.
At the upper right of the Arduino IDE screen you will see this:
A separate window will open. Look at the lower right and you will see a place to set the Baud Rate (Speed). Set it to 115200 as shown.
NOW you should see data scrolling by on the Serial Monitor screen. In my log cabin in Vermont all it found was my local WiFi Router:
And... That's All For Tonight!!
ESP32 EXAMPLE SKETCHES
NOTE: Find all sketches with SEARCH on upper right. Search on "YourESP32 Sketch"
YourESP32 Sketch NodeMCU32S SimpleBLINK This is specific to the nodeMCU-32S module with built-in LED
ESP32 Memory Size Questions
(From compiling bare sketch with only setup and loop)
Sketch uses 173740 bytes (13%) of program storage space. Maximum is 1310720 bytes.
Global variables use 13272 bytes (4%) of dynamic memory, leaving 314408 bytes for local variables. Maximum is 327680 bytes.
ESP32 Reference Publications
NOTE for Future USE
Micro-USB jack: The micro USB jack is used to connect the ESP32 to our computer through a USB cable. It is used to program the ESP module as well as can be used for serial debugging as it supports serial communication
EN Button: The EN button is the reset button of the ESP module. Pressing this button will reset the code running on the ESP module
Boot Button: This button is used to upload the Program from Arduino to the ESP module. It has to be pressed after clicking on the upload icon on the Arduino IDE. When the Boot button is pressed along with the EN button, ESP enters into firmware uploading mode. Do not play with this mode unless you know what you are doing.
Red LED: The Red LED on the board is used to indicate the power supply. It glows red when the board is powered.
Blue LED: The Blue LED on the board is connected to the GPIO pin. It can be turned on or off through programming. In some Chinese cloned boards like mine, this led might also be in red colour.
I/O pins: This is where major development has taken place. Unlike ESP8266, on ESP32 we can access all the I/O pin of the module through the break-out pins. These pins are capable of Digital Read/Write, Analog Read/Write, PWM, IIC, SPI, DAC and much more.