Test - Components

From ArduinoInfo
Jump to: navigation, search
YourDuino.com Low-Cost Starter Kit Components

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.30 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.30 AM.png

YourDuinoRobo1 Arduino-compatible with built-in 3-pin I/O connectors, higher current 3.3V supply
Upgraded Arduino Compatible: with ATMEGA328 Processor. BOTH 5.0V and 3.3V Operation with onboard regulator.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.24.13 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.24.13 AM.png

Opto-Isolated 2-channel Relay Board
With high-current relay, AC250V 10A ; DC30V 10A

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.39 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.39 AM.png

8CM Breadboard
Breadboard with power and Ground busses. This is used to make quick and easy and usually non-permanent connections between Arduino and different electronics components, chips, resistors, LEDs etc.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.05 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.05 AM.png

(5) Big push-button switches [Digital Input]
These large 12mm pushbutton switches have a nice CLICK action.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.14 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.14 AM.png

(2) 10K Potentiometers that fit breadboard well [Analog Input]
Hand operation - Plugs into breadboard.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.21 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.21 AM.png

(5) 10K PhotoResistors (Light sensors) [Analog Input]'
PhotoResistor type 5516 5-10K'. These are small Photoresistors that have a resistance of 10K ohms at 10 lux.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.29 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.29 AM.png

Digital temperature sensor DS18B20 [Digital Signal Input]
"1-Wire" Digital Temperature sensor.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.35 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.35 AM.png

(10) LEDs of 5 different colors, plus 220 ohm resistors [Digital or Analog Output]
1 RGB LED ( Red-Green-Blue Multicolor ) [Digital or Analog Output]

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.41 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.41 AM.png

Buzzer Module (makes sound with voltage applied) [Digital Output]
This small sound module can be driven by an Arduino output pin.When the pin is set to HIGH (with the - terminal of this module grounded) it puts out a constant buzz or beep.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.47 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.47 AM.png

Beeper Module (Makes different sounds/tones with Arduino TONE Library) [Analog Output]
This small sound module can be driven by an Arduino output pin. The + pin is marked on the case. A pulse of current will make it click. A series of pulses will cause it to output a tone, and you can control the frequency.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.53 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.53 AM.png

Servo Motor (Mechanical positioning from digital pulses] [Digital Signal Output]

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.24.05 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.24.05 AM.png

3-pin cable to separate wire ends that connect the Robo1 to any device

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.58 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.23.58 AM.png

3-pin cables with 3-pin connectors that fit the Robo1 and various Electronic Bricks etc.

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.48 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.48 AM.png

Pin Connector Strip

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.56 AM.png

Description: Macintosh HD:Users:maryaliceo:Desktop:Screen shot 2013-01-13 at 9.22.56 AM.png

40 wire flat rainbow color cable that can be separated to make many different cables